Tuesday, September 10, 2013

Birds and Bees Coaster Tiles Wall Hanging

Hello Paperclay® fans, and welcome back.  It is so hard to believe that the Summer is almost over and Fall is just around the corner.  It is plenty hot here, so it still feels like Summer to me.  And there are plenty of bees buzzing around, so I wanted to do something cool (no pun intended) with the honeycomb pieces I showed you how to make in my last post.  If you missed it, you can click here to see it.  This project is so easy to make, "even a caveman can do it".


Supplies Used:

Creative Paperclay® modeling material
Delight™ air dry modeling compound
Three 4"x 4" square coaster tiles
Six 4" x 4" squares print paper (Close To My Heart-Buzz and Bumble)
Push Molds (Mod Podge)(Premo)
Flexible plastic texture sheets - Music Background, Honeycomb (Carolee's Creations)
Distress ink (Wild Honey, Black Soot, Vintage Photo, Tarnished Brass, Brushed Pewter, Antiqued Bronze)
Acrylic Paints (Folkart Yellow Ochre)(Ceramcoat Charcoal)
Twinkling H20's (Mandarin Citrine, Golden Monarch, Ginger Peach, Mystic Blue, Iridescent Blue, Key Lime, Golden Jade, Rose Petal, Jasmine, Wild Plum)
Cropadile
3/8" gold metallic eyelets (8)
4 large jump rings, 2 small jump rings (Tim Holtz)
Decorative hanger (Melissa Frances)

Directions:

Make a 4" x 4" template from a scrap of printer paper, fold in half, and punch a hole through both halves near the edge, as shown.
Use this to mark placement of your holes for hanging your three coasters together, as shown in photo.
Cover each coaster, front and back, with the CTMH print papers, reversing the patterns, as shown.  (TIP:  Re-punch your holes each time you add the paper so you can find them easily.)  Now is a good time to distress ink the coaster edges.
Add eyelets to each hole, not only for strength, but to also finish off the holes.

Paint the honeycomb pieces first with Charcoal paint, then hit the tops with Yellow Ochre.
For the music background, spread a very thin layer of Paperclay® over the texture plate, the same as done for the honeycomb.  Allow it to dry before removing from the plate.
I was going for an old parchment paper look, so I added a very watered-down wash of Yellow Ochre, dabbing with a paper towel to get the color variations desired.  
Hit the high spots (the music notes) with Charcoal.
Next, I had made quite a few embellishment pieces using the Delight™ modeling material and various push molds.  Delight™ dries more flexible, even when it is a bit thick, so I used it for my embellishments in case I needed the flexibility.  So I laid out my three coasters, arranging my tiny pieces to see how I want to place them.  Nothing is glued down at this time.  
Color the various pieces to your liking.  I had a blast coloring these, and my inky fingers were a testament to that fun.  I colored the pieces using not only the acrylic paints, but also the distress stains and Twinkling H20s.  If my colors were too bright to my liking, I added a light coat of Vintage Photo distress stain.  That always tones down the brightness of colors.  And if you look carefully, you can see that the bird on the branch is so delicate and it broke apart into three pieces.  I am still going to use it and I am going to show you later on.

Now the fun of seeing your piece come to  life begins.  Adhere your Delight™ pieces in a pleasing arrangement, as shown on each of the three tiles below.



Add your jump rings through each of the eyelets, as shown below.  The larger jump rings go through the eyelets, then a smaller jump ring is used to join them.
Here are some close-up views of the pieces.  Don't you just love this little bird nest?
My cute little bumble bee.
And how about the rusty look on this key?
I was going for a bit of a rusty wrought iron look on these flourishes.
And remember the broken branches on this piece?  Normally, this would be my little secret, but I really wanted to show you to never give up because so many things in our art work can be "fixed" or "covered up".

Here is an example of where I layered one piece on top of another.  I love how the tiny pink flowers add to the piece.  I used them as fillers to bring all three coasters together.

These flowers and leaves were a bit too bright for me, so this is an example where a light coat of the Vintage Photo distress stain toned down the brightness.
Whew, I know this is a long post, but I have to admit, I had a blast making this piece.  I absolutely love working in mixed media, and Creative Paperclay® and Delight™ are certainly going on my list of mixed media to use for my altered art.   So, what will you make with it?  Well, you have a chance to show us.  

We are having a Halloween blog link up on 5 October.  What better way to showcase your work and share it with the world!!!  And you never know, you could win one of the prize giveaways.  So go ahead, give it a try.  Create something with Creative Paperclay® products and link up to the blog to enter to win!  
I am so glad you stopped by today, and I hope you enjoyed my project.  Please check out the Creative Paperclay® online store, and visit the blog for more inspiration.  I would also love it if you could visit my blog at Black Hole Art Studio.

Have a wonderful week, and play with some clay for the link up!

Barbara

4 comments:

Mrs Pretzel said...

I liked the honey comb when you shared the sneak peek and tip the other day, but it really pops on this project!! The music "paper" is absolutely my fave.

Barbara Rankin said...

Thanks, Rachel. It is paper thin and very flexible. I'm in love with my new discovery. :)

Linda Hess said...

What a fabulous project! So many components and they fit together perfectly. I agree that this is the perfect project to showcase your honeycomb :-)

dawnmercedes said...

this is such a pretty thing! would love it for a spring time home decor idea!!